No matter how steady your hunting rifle, hitting at any range presumes a proper zero.
Because a bullet follows the bore axis out the muzzle, it will fly nearly parallel to the line of sight until gravity pulls it unacceptably off course. Bear in mind that a bullet’s path is never perfectly straight. Gravity grabs the projectile as soon as it exits the rifle. In zeroing, you adjust the sight so your straight line of vision intersects the bullet’s parabolic path not far from the muzzle, then travels below it until the two merge at the zero distance.
You are reading: How to Zero Your Deer Rifle's Scope for the Best Accuracy
Beyond that, the bullet drops ever more steeply away from the line of sight. Zeroing, or sighting in, is simply aligning the sights (scope) on your rifle so the bullet hits where you aim at a certain distance. A rifle cannot be manipulated to change the bullet’s path. It is the sight alone that is to be adjusted. Windage and elevation adjustments move the rear sight or a scope’s reticle so it directs your eye to where the bullet hits at a given distance. You pick the range.
It’s a common misconception that a bullet rises above line of bore during its flight. It does not. It cannot. Sight-line is not parallel to bore line, but, rather, at a slightly converging angle. The line of sight dips below bore line and the bullet’s arc. Sightline never again meets bore line. Both are straight and, after crossing, diverge. A bullet hits above sightline at midrange, because sightline has been purposefully angled down through its trajectory. The bullet falls to intersect it at greater range. If the sightline were parallel with the bore, it would never touch the bullet’s arc.
The most useful zero depends on the bullet’s trajectory and on how far you intend to shoot. For most big-game rifles, a 200-yard zero makes sense. Sight in there with a .30-06 or a similar cartridge, and your bullet will stay within three vertical inches of point of aim out to 250 yards or so. A three-inch vertical error still gives you a killing strike in the ribs of big-game animals. The 200-yard zero permits “dead-on” aim as far as most marksmen can hit in the field. At 300 yards you’ll have to shade high.
Why not zero at 250 or even 300? Well, with flat-shooting rounds like Weatherby’s .270 Magnum, you can. A 200-yard zero puts its 140-grain bullet only 1½ inches over sightline at l00. Adjust the scope so the rifle shoots three inches high at l00, and you’ll reach 300 yards with a mere one inch of drop! By the same logic, a zero for the likes of the .30-30 is best kept short of 200 yards, otherwise the bullet’s steep arc will put it a whopping five inches high at its apex (some distance beyond 100).
Read More : The .45-70 Gov't: A Legendary Deer Hunting Cartridge
You’re better off zeroing hunting rifles so you won’t ever have to hold low. Remember that shots too long for a point-blank hold with a 200-yard zero are uncommon. Most game, even in open country, is killed well inside 300 yards. I recall a fellow shooting over the back of a magnificent bull elk at 200 because he’d zeroed his .300 Weatherby at 400.
The best zero for a .30-30 carbine may have less to do with the limited range of the cartridge than the more limited range at which you can shoot accurately with its iron sights—or the even more limited distance you can see in typical whitetail cover! While a 150-yard zero is reasonable, a 100-yard zero may be even more practical, especially if you hunt where most of your shots come very close.
One reason many hunters like to zero long is that they overestimate yardage in the field. One fellow told me recently that his .30 magnum could outshoot any rifle between 800 and 900 yards and that he had toppled a buck at 700 steps by holding just over its withers. Now, even a congressman would have blushed spinning that yarn.
The flattest-shooting cartridges land their bullets nearly three feet low at 500 yards, when the rifle is zeroed at 200. To keep a .270 Weatherby bullet (muzzle velocity 3,375 fps) from sagging more than a foot at 700 yards, you’d have to zero at over 600! That would put the bullet roughly two feet high at 300 and 400. It would be plunging so rapidly at 700 that, if you misjudged range by just 10 percent, you’d miss the deer’s vitals!
When zeroing, you’ll save time and ammunition separating the task into two stages, bore sighting and shooting. Bore sighting isn’t necessary. It’s merely a short-cut to the end of the shooting stage. Shooting is necessary. A rifle that’s only bore-sighted is not zeroed!
Zeroing Your Rifle After satisfactory results at 100 yards, move the target to 200 or your zero range. During the last stages of zeroing, make sight changes only after three-shot groups. A single shot can be misleading.
Read More : This Whitetail Behavior is Most Puzzling | Whitetail Wisdom Blog | Deer & Deer Hunting
First shots to zero should be at 35 yards, whether or not you’ve bore-sighted. After each shot at 35, move the rear sight or scope dial in the direction you want the bullet to go until you hit point of aim. (Mind the dial arrows! European scope knobs typically turn clockwise to move impact up and right, while clockwise rotation on scopes built for the American market moves impact down and left.)
Now, switch to a 100-yard target. I prefer that bullets from flat-shooting big-game rounds hit two to 2½ inches high at this range. Depending on the load, the rifle will then put its bullets close to point of aim at 200 yards.
Windage and elevation dial “clicks” or graduations are engineered to shift bullet impact a precise measure at 100 yards. That’s most commonly ¼-minute of angle. A minute of angle is 1.047 inches at 100 yards (but shooters know it as an inch at that range), two inches at 200, and so on. A target scope may have graduations as fine as 1/8-minute; scopes intended for long shooting incorporate coarser elevation detents—½-minute or even 1-minute clicks—to lift point of impact with less dial movement. A greater range of adjustment results, as well. When you can’t turn the dial past zero, you also avoid the possibility of “full rotation” error, which can cause spectacular misses. European dials are typically marked in centimeters.
Another method as fast as counting clicks to move bullet impact, is to secure your rifle so the reticle centers the target as it did when you last fired. Then, without moving the rifle, turn the dials until your reticle kisses the previous bullet hole.Even with a benchrest, it’s easy to make a bad shot. In fact, a bench can give you a false sense of stability, prompting fast, sloppy shooting. No matter how steady you think you are, check your position before each shot and fire carefully. Call your shots. To learn where your bullets really hit at long range (and how great their dispersion), fire at 300, then 400 yards. For hunting, that’s as far as you’ll likely have occasion to shoot. If longer pokes are on the agenda, find a place to test your rifle and your zero farther downrange. It’s worth the trouble! There’s no reason to fire at game farther than you’ve tested your loads and your holds on paper!
Tactical rifles in .338 Lapua and .50 BMG, built to hurl match bullets at targets very far off, have been joined by sporting rifles with exceptional reach. Zeroing at long range introduces a couple special considerations most hunters needn’t consider. One is the range of dial movement on the scope’s elevation adjustment. Consider installing a slanted Picatinny rail, one whose front end is lower than the rear. Such a rail has “gain” and puts the scope at an angle to the bore, so that, when you center the dial in its range, the scope’s axis (line of sight) crosses the bullet’s path farther away. You get a longer zero without using all the adjustment. The more nearly centered the erector assembly (which holds your reticle), the better. A lens gives you the best picture through its middle. Barrett supplies rails with gain for its .50-caliber rifles.
Hunting rifles with 200-yard zeros won’t do well at a 1,000-yard match, because shooters would have to aim several feet over the target frame. There’s too little elevation adjustment in many scopes to get a 1,000-yard zero. If you could dial in enough lift to achieve a 600-yard zero with your .30-06, you’d still have to aim 17 feet high to hit a 1,000-yard bull’s-eye! Of course, a truly long-range zero comes with severe mid-range penalties. Even that 600-yard zero would put ’06 bullets 2½ feet high at 300 yards!
Source: https://raysthesteaks.com
Category: Hunting